User Tools

Site Tools


en:wiki:funktionen:td-functions:cut_n_window

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
en:wiki:funktionen:td-functions:cut_n_window [02/07/2016 23:34] hamishen:wiki:funktionen:td-functions:cut_n_window [07/07/2016 09:28] (current) uli
Line 5: Line 5:
 \\ \\
 **Description** \\ **Description** \\
-If a filter is convolved​​​ with another filter the filter length doubles. Since the convolved filter needs to be the correct length for further use, Cut 'n Window allows it to be "trimmed" down to size.+Basically CutNWindow is a function to cut a desired part of a pulse response. If e.g. a filter is convolved​​​ with another filter the filter length doubles. Since the convolved filter needs to be the correct length for further use, Cut 'n Window allows it to be "trimmed" down to size.
  
 \\ \\
 **Options:** **Options:**
  
-   * //Length://  Specifies the output filter length +   * //Length://  Specifies the output filter length. The combobox allows a quick selection of preferred lengths (power of two). The edit field allows to define also other lengths. 
-  * //Position/Count: Together with the radio buttons to the right and the checkbox below, specifies where the new filter starts and ends// +  * //Position/Count: //Together with the radio buttons to the right and the checkbox below, specifies where the new filter starts and ends 
-  * //Start position: If selected, Position/Count specifies the beginning sample of the new filter relative to the beginning of the input filter// +  * //Start position: //If selected, Position/Count specifies the beginning sample of the new filter relative to the beginning of the input filter 
-  * //before Peak: If selected, Position/Count specifies the beginning sample of the new filter in samples before the peak of the input filter. Higher Position/Count therefore moves the first sample of the new filter to the left, or earlier in time, which is the opposite behavior to the case where Start position is selected.// +  * //before Peak: //If selected, Position/Count specifies the beginning sample of the new filter in samples before the maximum peak of the input filter. Higher Position/Count therefore moves the first sample of the new filter to the left, or earlier in time, which is the opposite behavior to the case where Start position is selected. 
-  * //Before peak in area ! not allowed !://  Don'select this option[It allows the new filter to have first sample before the first sample of the input filter. If you need this, you know who you are.]+  * //Before peak in area !://  It is possible to select an area by setting the markers in the time-domain chart (left/right mouse-click). Then CutNWindow uses the max. peak within this area as referenceThis allows e.g. to cut a part around peak caused by reflections. It the markers are not defined then the comment "//! not allowed !//" appears.
   * //peak symmetric: //The new filter starts exactly half its length before the peak. If checked, Position/Count is ignored.   * //peak symmetric: //The new filter starts exactly half its length before the peak. If checked, Position/Count is ignored.
-  * //Remove DC://  Removes any zero frequency components of the output filter. Usually a good idea to leave checked. (Leave it checked unless you have a specfic reason and know what you are doing. DC needs to be removed before filters are used to drive loudspeakers.)+  * //Remove DC://  filter pulse response can contain a DC offset. It will be removed if the checkbox is ticked. Usually a good idea to leave checked. (Leave it checked unless you have a specfic reason and know what you are doing.)
   * //Window (Blackman Optimal): //Occasionally needed when Cut 'n Window is used to shorten filters if the beginning or end of the output filter occurs at a time when the value of the input filter is significantly different from zero. In this case it removes spurious high frequency components that would otherwise be created, at the cost of some modification of the frequency response. However a filter so short inevitably leads to compromises.   * //Window (Blackman Optimal): //Occasionally needed when Cut 'n Window is used to shorten filters if the beginning or end of the output filter occurs at a time when the value of the input filter is significantly different from zero. In this case it removes spurious high frequency components that would otherwise be created, at the cost of some modification of the frequency response. However a filter so short inevitably leads to compromises.
  
  
en/wiki/funktionen/td-functions/cut_n_window.1467502444.txt.gz · Last modified: 02/07/2016 23:34 by hamish

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki